Published on : 21 November 2026
Shipping Boxes for Artwork: The Complete 2026 UK Guide
You've sold a painting to someone four hundred miles away. The payment cleared, the label is printed, and there's a box in the hallway that looks about the right size. That's where most artwork gets damaged, not in the back of a van, but at the kitchen table where the box was chosen for convenience.
Shipping boxes for artwork get treated as a size question when they're a materials and evidence question. The carton is the easy part. What sits between the carton and the surface, how the piece is immobilised inside it, and what you can prove afterwards are what decide whether the work arrives intact and whether a claim survives if it doesn't.
This guide works through all of it in the order you'll use it. If you want the short version, it's this: match the contact layer to the medium, size the outer shell to the sealed parcel, and photograph everything.
What Makes Shipping Artwork Different
Say a canvas goes out wrapped in three layers of bubble wrap and taped into a box with two fingers of space at each end. It arrives with a faint grid printed into the paint film and a split at one corner of the stretcher. Nothing was obviously mishandled. The wrap pressed on the surface and the slack let the piece build momentum, so every drop landed as a jolt concentrated into the frame.
Artwork differs from a normal parcel in three ways.
- Reactive surfaces. Paint, varnish, pastel and photographic emulsions can stick, abrade or lift when a film is pressed against them, and the damage often shows up days after delivery.
- Load-concentrating structures. A frame corner, a stretcher bar or the edge of a glazed panel takes a knock across a few square centimetres and passes that force straight into the work.
- Value that changes the process. A crushed carton on a household item is a refund. On a painting it's a condition report, a courier file and an insurer.
The principle everything below is built on. The box is only the outer shell. Protection comes from a system of surface layers, rigid support, cushioning and immobilisation, each matched to the medium you're sending.
The sections that follow build that system in order: a box-selection table by artwork type, the five-layer protection model, the cushioning materials that are safe against each surface and the ones that aren't, a numbered packing routine, three worked shipments with real dimensions, and the evidence checklist that decides whether a claim holds up.
When a piece moves beyond a domestic courier into international freight, your packing becomes one link in a longer handling chain where documentation matters as much as cushioning. The Approved Jets air freight playbook sets out how that chain is run and recorded.
Choose the Right Box for Each Type of Artwork
The fastest way to stop guessing at shipping boxes for artwork is to start from the object rather than the shelf. Find the row closest to what you're sending, read across, and you have the construction, the clearance and the internal layers in one line.
Box and protection choices by artwork type
| Artwork type | Recommended box | Size allowance | Key protection inside | Notes |
|---|---|---|---|---|
| Unframed print or photograph, A4 to A3 | Rigid single-wall postal box with board stiffeners | Artwork size plus 2 to 3 cm | Acid-free tissue sleeve, rigid backing board | Keep flat and add a waterproof outer layer for wet weather |
| Framed print or photo under glass | Double-wall box | Frame plus 5 cm all round | Glass tape, foam corner protectors, bubble wrap, snug void fill | Ship on edge, never flat |
| Small or medium canvas, oil or acrylic | Double-wall removal box | Canvas plus 5 to 8 cm | Glassine face layer, bubble wrap over the interleaf, edge protectors | Never let bubble wrap touch the paint |
| Large canvas or oversized framed work | Reinforced double-wall box or plywood crate | Piece plus 8 to 10 cm | Foam sheeting, moving blanket layer, edge protection | Check carrier size limits before you pack |
| Pastel, charcoal or soft pencil drawing | Rigid box with a protected face | Artwork plus 3 to 5 cm | Acid-free tissue, rigid backboard, no Melinex | Friable media need face clearance, not pressure |
| Ceramic or sculptural piece | Double-wall box, double-boxed if valuable | Piece plus 5 cm all round | Moulded foam or bubble cocoon, centred in the box | Fill every void so nothing shifts |
Double-wall corrugated is the default outer shell for anything framed, glazed or valuable, because it resists compression and stacking loads rather than folding under them. Single-wall rigid postal boxes earn their place only for small flat works that are backed with stiff board. For a canvas in the 40 to 60 cm range, a medium double-wall box such as an 18x18x12" Removal boxes MEDIUM double walled gives you a rigid shell with room to build clearance around the stretcher.
Measure the sealed parcel, not the painting
The measurement that matters is the finished package. Add the corner protectors, the bubble wrap, the face and back boards, the interleaf and the carton wall, then measure. On framed work allow roughly 5 cm clearance all round; on flat paper pieces 2 to 3 cm is usually enough because the rigid boards are doing the work, not the cushioning.
Weigh the parcel after sealing rather than before. Royal Mail counts the box and every layer of packaging in the shipment weight, and its standard parcel ceiling is 61 × 46 × 46 cm and 20 kg, as set out in its packaging and sending heavy items guidance. Anything above that gets split into separate boxes or moves to a different service.
The carrier limit that overrides everything else
That ceiling is the constraint most sellers hit without noticing. A 60 × 80 cm framed print with 5 cm of protection on each side lands at roughly 70 × 90 cm, which is inside the weight limit and well outside the size limit. Oversized artwork packaging can end up handled by Parcelforce or pushed into a freight decision, so measure the sealed carton before you book, not after.
Royal Mail's own packing advice is worth following with artwork: a sturdy crush-resistant box, minimal internal void space, cushioning on every side, and strong tape across seams and edges. A rigid double-wall carton resists compression, a snug internal fit prevents sliding, and a continuous cushioning layer spreads shock instead of letting a single frame corner absorb it.
If you're choosing between constructions, the Double Walled Cardboard Boxes range covers the sizes that suit framed and stretched work, and it's where I'd start for anything over A3. Never reuse a tired or previously crushed carton for artwork. Creased fluting has already lost the compression strength you're paying for.
Build the Five-Layer Protection System
A carton gets judged on journey length, vibration exposure, fragility and the distance between the artwork and the outer wall. Board grade and finished dimensions are the entry ticket; the layer plan decides whether those four stay under control.
Start at the surface and build outward.
- Surface interleaf. Glassine or acid-free tissue sits directly against the work so the artwork touches nothing else. Its job is to prevent sticking, burnishing and transfer.
- Rigid face and back support. A board or backboard across both faces stops a frame or canvas flexing when weight is applied to the carton.
- Edge and corner protection. Foam or board over projecting corners and stretcher bars puts something replaceable between the knock and the frame.
- Cushioning and void fill. Wrap and fill spread shock across the whole piece and leave no route for movement in any direction.
- The structural outer box. Double-wall board resists compression and stacking loads and holds the inner system in shape.
The analogy that makes it stick. The outer box is the car body. The inner layers are the suspension. A rigid shell with no suspension transmits every jolt straight to what it carries.
The British Museum's transport vibration research reports a 2019 project comparing standard crates with crates fitted with extra vibration-mitigation systems, then applying the approach to nine crates on the 2021 touring exhibition Mummies of ancient Egypt: rediscovering six lives and to a crate calculator for grouping objects by weight, geometry and fragility. The useful lesson is the method: decide the journey risk first, then give each risk a named layer.
Longer or higher-risk legs can justify an inner case inside a lined outer crate, while a short domestic move may let the painting travel in the outer crate alone. Same painting, different journey, different design.
Before you add a layer, say what it does. If you cannot name the job, it is bulk, and bulk that restrains nothing can make the parcel worse. Foam profiles for corners and edges are the layer most often skipped and the one that stops frames cracking, so keep Edge Protectors for Corner and Edge Protection with the rest of the kit.
Match Cushioning Materials to the Artwork Surface
More cushioning is not automatically safer. National Museums Scotland's collections-care guidance says packing has to protect against dust, environmental change, vibration and surface abrasion, not just impact, and it warns against a list of materials that are often chosen first because they can release harmful gases, transfer acidity or damage objects over time. An unsuitable material in direct contact with a drawing can cause chemical or surface damage long after a parcel arrives with no visible marks on the outside.
Cushioning and contact materials for artwork
| Material | Use it for | Keep it away from | Why it matters |
|---|---|---|---|
| Acid-free tissue | First contact layer for prints, drawings and unframed paper | Nothing in normal artwork use | Chemically stable barrier that won't stain or transfer acid |
| Glassine | Smooth face protection for paintings, glazed works and photographs | Friable media that need a loose tissue layer | Smooth, non-stick barrier against abrasion and rubbing |
| Melinex (polyester) sleeve | Prints, photographs and stable drawings | Chalk, charcoal, pastel and soft pencil | Inert clear sleeve, but it can lift friable media off the paper |
| Bubble wrap | Outer cushioning over an interleaf | Direct contact with paint, varnish, pastel or unprotected glass | Pressure points can imprint, stick or mark the surface |
| Foam edge and corner protectors | Frame corners, stretcher bars and box edges | Painted, varnished or pastel faces | Absorbs the corner impacts that crack frames and glazing |
| Newspaper | Nothing that touches artwork | All direct artwork contact | Acids and inks migrate into paper and cause staining |
| Polystyrene peanuts and ordinary adhesive tape | Void fill away from the piece; tape on packaging only | Any direct contact with the artwork | Can shed, stick, react or leave residue over time |
What goes next to the surface
For paper and unframed work, the museum's guidance points to acid-free tissue, Melinex sleeves or acid-free card, with one firm exception: Melinex is unsuitable for friable media such as chalk, charcoal, pastels and soft pencil. The sleeve can lift loose particles straight off the sheet. On a charcoal drawing, tissue and a rigid board do the job a sleeve would ruin.
For paintings, glassine sits against the face and bubble wrap goes outside it, never on the paint. A stretched canvas needs its support to meet the stretcher bars rather than the painted fabric, so pressure travels around the perimeter instead of through the surface.
The materials that stain
Newspaper is the classic mistake because it's free and it's everywhere. Wood, wool, felt, ordinary tape, polystyrene and some biodegradable fillers sit in the same category for the same reason: they can off-gas, transfer acid or leave a residue that surfaces months later as yellowing.
Audit rule: identify the medium and the surface condition before you choose the wrap. Ordinary corrugated board is the structural shell, never the contact layer.
Run your materials list against the table above, row by row, before the piece comes out of the studio. If any item in the box will touch the artwork directly, it needs to be on the safe side of that column.
Bubble wrap earns its place as the cushioning layer rather than the contact layer, and a wide roll lets you wrap a large stretcher in one continuous pass instead of patching it. Rolls, bags and pouches are grouped together under bubble wrap rolls and protective packaging if you're restocking.
Order the Complete Packing Kit Before Packing Day
A box can be the right size and still fail the shipment if the glassine, corners or labels arrive after the courier. Order in the sequence the layers are used, so the kit lands as one working system.
- Do a dry fit and measure the sealed assembly. Mock up the contact layer, rigid support and corner protection first, then measure the complete package rather than the bare artwork.
- Choose the shell by construction, then dimensions, then quantity. Use double-wall where weight, stacking or courier handling justifies it, and size it to the sealed assembly.
- Order every contact and cushioning item in the same basket. Glassine or acid-free tissue, boards, foam edges or corners, bubble wrap and void fill should match the medium and surface you identified.
- Finish with consumables and claim-ready supplies. Tape, fragile labels, outer marking and a simple condition checklist should be in hand before dispatch day, so the piece is not sitting half-wrapped waiting for a delivery.
The Archives and Records Association's storage enclosure guidance, citing BS 4971:2017, gives a useful buying test: enclosure materials and adhesives should not contribute to fading or yellow staining, the enclosure should fit so contents cannot slide, and surfaces should not scratch or abrade. Treat those as pass or fail checks when comparing products.
Storage & Removal Boxes Ltd supplies double-walled removal boxes, bubble wrap rolls, foam protectors and specialist packing materials, with UK-wide delivery and stated same-day dispatch for orders placed before 3pm, Monday to Friday. Its double-wall boxes protect fragile goods during a move, and the oversized bubble wrap bags with self-sealing flap are made for artwork, mirrors or electronics in storage or transit. To cover boxes and consumables together, use House Moving Kits & Boxes.
How to Pack Artwork for Shipping Step by Step
Work through this in order and don't skip ahead. Each step exists because of a specific failure.
- Measure and photograph the piece. Front, back, signature, frame and glazing, in clear light. Two minutes here is the difference between a claim and a conversation. If the work is a canvas you've framed yourself, check the mounting before you wrap it: the same stretcher and frame decisions you'd weigh up to frame your album lyric canvas determine how the piece needs to be supported inside the box.
- Tape the glazing. Strips of masking tape or low-tack glass tape across the glass, in a grid or an X, so shards stay together if it breaks. National Museums Scotland recommends this for pictures and mirrors in its handling guidelines, along with carrying pictures vertically rather than horizontally. The common slip is skipping the tape because the glass looks fine.
- Add the surface interleaf. Glassine over a painting, acid-free tissue over paper. Never tape onto the artwork itself. For thin paper works, the same guidance suggests Melinex sleeves or acid-free tissue, with a tray between tissue layers or between two sheets of acid-free card when the item is unstable in a sleeve, secured against movement with a pinning method (National Museums Scotland on packing paper and unframed artworks).
- Add rigid face and back boards. The piece should not flex when you press a thumb gently on the board. Foam corner protectors go on frames at this stage, over the corner rather than on the face.
- Wrap in two to three layers of bubble wrap. Tape the wrap to itself so the layers hold as a sleeve around the boards. For a large canvas, the 1500mm Wide Standard Bubble Wrap Roll – Large Rolls for Heavy Duty Protection covers a full stretcher in one pass; these are 1500mm rolls with standard small bubbles, made for very large and delicate items.
- Line the box and centre the piece. A cushioning base first, then the wrapped work, then fill every void. The fit should be snug enough that nothing shifts and loose enough that you can get a hand in to lift the piece out.
- Close it and shake-test it. A gentle tilt and turn, listening for movement. If anything knocks or slides, reopen it and add fill. Don't shake hard; the check is for restraint, not for durability.
- Seal, label, weigh and measure. Tape every seam and edge, mark fragile and this way up, then put the sealed parcel on the scales and against the tape measure before you book the carrier. Record both figures next to the photographs from step one, because that pairing is what an insurer asks for.
Steps three to six are what conservation standards mean by packing an object properly before transport: protective materials suited to the object's condition, and packaging that delivers the protection, environmental control and security it needs in its predicted environment. The box is only the outer shell of that system.
The three slips that cause most of the damage
Skipping the interleaf because bubble wrap is already in your hand. Direct contact is where sticking, imprinting and surface loss start.
Packing flat art horizontally. Pictures travel better on edge, which is why the tape, the corner protectors and the vertical orientation markings all point the same way.
Wrapping before photographing. Once the piece is inside tissue and bubble, the condition record is gone. If the carrier disputes the damage later, the step one photos are all you have.
Packing Setups for Common Artwork Shipments
Three real-world setups, with the dimensions and the one decision that makes each one safe.
An A2 framed photograph going by post. The frame measures about 61 × 51 cm, which already sits on the standard parcel ceiling from the size calculation earlier. Add corner protectors and a double-wall carton and the sealed width runs past it, so the decision is box depth. Choose a shallow double-wall carton that keeps the finished parcel inside the limit and under 20 kg, and if you can't, move the piece to a courier instead of forcing it. Glass tape across the glazing, foam corners, one layer of bubble wrap over the frame and snug fill at the edges.
A 60 × 80 cm acrylic canvas sold online. Glassine against the face, foam edge protectors on the stretcher, two layers of bubble wrap over the interleaf, then a double-wall box of roughly 75 × 95 cm with fill on all six faces. A carton that size sits outside standard parcel dimensions, so this one gets a courier booking rather than a post office queue. It ships on edge with this-way-up labels and goods-in-transit cover, because the value justifies it.
An unframed charcoal drawing. Sellers often ship a small charcoal in a plastic sleeve, and the static lifts the friable medium straight off the paper. Acid-free tissue front and back, the sheet supported between two sheets of acid-free card, deliberately no Melinex. It goes into a rigid do-not-bend postal box with the card sandwich immobilised by void fill, so the artwork can't slide against the box wall.
The charcoal is the smallest and lightest of the three and carries the most surface risk. Choose the contact layer by medium, not by weight.
Map your own piece to the nearest of these three, then adjust the carton using the table further up. The artwork type sets the construction; the finished dimensions set the size; the medium sets the contact layer.
Evidence and Insurance Before You Dispatch
Carrier compensation is often calculated on parcel weight, not on the artwork's value. That formula suits a heavy box of books and fails a light, high-value canvas, which is why the Ship Art advice published by Flight Logistics warns that standard cover can be inadequate, and why insurers may also ask for photographic evidence of the piece's condition before shipping and of the packing process itself.
For higher-value pieces, separate all-risks or goods-in-transit cover is worth arranging before the booking, not after a problem. The UK Government Indemnity Scheme shows how wide the exposure runs: its cover can apply to objects on loan while in transit to and from a borrowing venue, in storage, during installation, on display and during dismantling, as an alternative to commercial insurance for qualifying loans (Government Indemnity Scheme). A single dispatch can pass through several of the same stages.
The dispatch evidence protocol is short and strictly required.
- Photograph the artwork front, back, signature, frame and glazing before anything is wrapped.
- Photograph each packing stage, including the contact layer, the boards, the corner protectors and the closed carton.
- Record the details. Dimensions, medium, declared value and the order reference, kept with the images.
- Keep the receipts for materials and the carrier booking.
- Read the exclusions for glass, artwork and surface damage before you pay, and check the carrier's compensation limit.
- Retain the carton and internal packaging until the claim window closes, because an assessor may want to see how the piece was restrained.
- Inspect on arrival and photograph any damage before unpacking further, so cosmetic box damage isn't confused with proof of damage to the work.
Two transit checks belong in the booking itself. Confirm the carrier won't leave a painting in an unheated vehicle in sub-zero weather, because Museums Galleries Scotland's advice on caring for paintings and frames warns that cold at that level can damage acrylic paint. The same guidance recommends checking a courier's risk assessments, method statements, insurance and qualifications before transport. Then mark the outside of the parcel with warning labels for boxes, so orientation and fragility instructions sit on the carton rather than only in your phone gallery.
Check the sizes, quantities and label packs on the Storage & Removal Boxes Ltd site before your next dispatch.